AUTONET TV

STRAIGHT TALK ABOUT STEERING (Loose Steering)

Perhaps you've heard someone use the term "loose steering." And it's pretty much what it sounds like.  You turn the steering wheel and the vehicle's wheels don't seem to go exactly where you thought you were pointing them.  You have to constantly make steering adjustments. 

Loose steering is sloppy steering, and it can be a safety hazard.  You need to be able to control your vehicle with pretty much the same precision as the way it was when it came off the assembly line.  

If the steering in your vehicle is starting to feel loose and sloppy, there may be some significant suspension issues that need examining by a trained technician.

How do you know if your vehicle needs to be looked at? Try turning the steering wheel and see how much play is in it.  One rule of thumb: if you can turn it the distance of a quarter and a dime placed side by side without seeing the outside wheels move, it's time to have it inspected by one of our technicians.

Our Muffler & Go technician will examine those components that are supposed to work together to make sure your steering is tight and precise.  They are linked together by things called (of course) linkages.

When these linkage components were new, they all fit together tightly and moved together to make sure your wheels responded quickly and precisely to your movements of the steering wheel.   

But hit a few potholes, travel over a couple of rough railroad tracks and those metal components can be damaged or bent.  Given enough time, they will simply wear out. Our trained Muffler & Go technician can inspect all of those parts and determine what needs to be repaired and/or replaced.  

Keep your steering tight.  Loose or sloppy steering can be dangerous.  Thank goodness it usually warns you in plenty of time before it fails completely. Just straight talk… about steering.

Muffler & Go
1478 N Leroy St
Fenton, MI 48430
(810) 629-1066
http://www.mufflerandgo.net

Some New Boots (Suspension Maintenance)

There are some boots that don't come in a shoe box and aren't worn on your feet.  They are called axle or CV boots, and they can be important parts for many vehicles.

That CV stands for constant velocity.  CV axles are mainly used in front-wheel drive and all-wheel drive vehicles. They're also used in some rear-wheel drive vehicles with independent suspensions.  They have two CV joints, one inner and one outer, placed between the axle and the drive wheels.  That way the vehicle's engine power can drive the wheels, no matter what angle they are.  They also adjust for the different speeds wheels turn as they go around corners. 

Because roads are full of all sorts of hazards (dirt, oil, water, grime), these CV joints need to be protected.  They also have grease in them to keep the bearings moving smoothly.  That's the job of the rubber boots that are supposed to keep that debris out.  These CV or axle boots are made of rubber or plastic and usually last a long time without any problem.  But sometimes they fail, either from being hit by debris or age causing the rubber or plastic to deteriorate.  That can allow the grease to leak out of the joint and the moisture to get in.  And that's where the trouble is.

So it's important to have a vehicle's CV boots checked periodically, especially when they begin to have more than 100,000 miles/160,000 kilometers on them.  A technician inspects them for tears or cracks.  Sometimes if the problems are found early enough, the boots can be replaced and the joints can be re-packed with grease. 

But sometimes the CV joint can wear out even though the boot is intact.  When the CV joint fails, you might hear a grinding, humming or clicking noise and feel vibration.

Some of these can be difficult to access for service, so many service advisors will recommend replacing the joints and boots at the same time.  Just remember, new CV boots won't make a fashion statement, but they will keep your vehicle going down the road for years to come.

Muffler & Go
1478 N Leroy St
Fenton, MI 48430
(810) 629-1066
http://www.mufflerandgo.net

Getting from E to F (Fuel Gauge Problems)

Who thinks about their fuel gauge?  You probably don't… until it doesn't work any more.  Then you have to guess how much fuel is in your tank, and that's no way to live life on the road. 

Fuel gauges, like every other part in your vehicle, can fail.  And when yours stops working, you will probably want to head over to your service facility soon, because no one relishes running out of fuel.

The fuel gauge system is much more than just the gauge you can see on your instrument panel. Most systems have a float inside the fuel tank that goes up and down depending on the fuel level.  It's called the fuel sending unit, and it sends an electrical signal to the gauge (on the dash) telling it to display how much fuel is left in the tank. 

So, what could go wrong?  Well, a few things.  For one thing, corrosion from bad fuel can cause it to stick and it won't move up and down any more.  So you could fill up your tank and the gauge would still read Empty.  If a sending unit needs to be replaced, often the parts can be costly. The good news is that fuel sending units rarely fail and most drivers will never have one go bad.

Other things that can go wrong? An electrical problem could cause a fuse to blow and you won't get a reading at all.  A technician can figure out where that electrical problem is and how to repair it.  Finally, it's possible for the gauge itself (on the instrument panel) to fail.

One thing to keep in mind is if your fuel gauge isn't working, you might be tempted to carry around an extra container of fuel.  That's ok if it's outside the cabin, such as in the bed of a pickup.  But if you carry it inside the cabin or trunk, fuel fumes can be very dangerous for your health, even fatal.

A working fuel gauge gives you peace of mind… so you'll never have that "empty" feeling.

Muffler & Go
1478 N Leroy St
Fenton, MI 48430
(810) 629-1066
http://www.mufflerandgo.net

For Brakes' Sake (Brake Rotor Service in Fenton)

Think of how much abuse your brakes take. Day in and day out, they stop your vehicle when it's going fast and when it's going slow. Maybe your vehicle has been vibrating when you brake, or maybe it seems like your stopping distance is a little bit longer than it used to be.

Then it's time to get your brakes checked out. After all, you have to be able to stop if you want to be safe. Nearly all newer vehicles have disc brakes on the front, and many have that type of brake on all four wheels. That makes it likely you'll be getting disc brakes fixed at some time in your vehicle's lifetime.

Knowing how disc brakes work is as easy as riding a bicycle. If your bike had hand brakes, you'll probably remember a mechanism that squeezed a couple of pads on each side of your bicycle wheel when you applied the brakes. Disc brakes are similar; but instead of the bike wheel, there's a metal disc instead. If that disc is warped or has irregularities in it, it's going to vibrate.

It used to be that rotors were thick, and when they warped, a technician could "turn" them to scrape off a layer of metal so their sides were straight again. The latest vehicles are using thinner, lighter rotors with a slightly different construction. Now, it's likely that rotors that are resurfaced this way will not have enough metal left to work safely. In fact, some manufacturers advise only replacing rotors that are worn out.

Newer designs have reduced rotor prices, and in many cases, the labor cost of turning the rotors is higher than buying new. There are times, though, where your rotors can be resurfaced and still meet manufacturer specifications.

If you have a rotor replaced on one side of your vehicle, it might be a good idea to replace rotors on the other side, too.

Maybe you're looking for the new rotors to last longer than the ones that were on there. New technologies can offer a longer lifespan in a premium rotor. Armed with knowing the type of driving you do, you and your Muffler & Go service advisor can make the best decision on which direction you want to go with your new brakes.

Muffler & Go
1478 N Leroy St
Fenton, MI 48430
(810) 629-1066
http://www.mufflerandgo.net